In this article, we are going to discuss how to fix the fiberglass frame and fiberglass top of the car.
First, take out the fiber glass on the top of your car.
If you can, use a nail or an electric saw.
Do not use a razor blade or a scalpel.
Once the fiber has been removed, put it back in place.
If the fiber is bent, use an awl or pliers to remove it.
If it’s warped, you may have to use a flathead screwdriver.
You can also use a screwdriver to gently remove the bent part.
You may have also to bend the bent fiberglass part in half.
This can be tricky, so be careful.
Once you have the bent piece, it is time to fix it.
First put the fiber into a bag.
You will need to use plastic bags to keep the fiber from sticking to the car and from drying out.
Put some water inside the bag to keep it from getting dirty.
Make sure the bag is filled with at least one inch of water.
When you put the bag inside the car, be careful not to disturb the fiber, as you want it to stay as dry as possible.
Now, take the fiber out of the bag.
This is the part that needs to be fixed.
You want to use the awl to pull the fiber apart.
You need to make sure the fibers are straight and not curved.
Make a mark on the fiber with a pencil.
You should be able to make the mark on your finger.
Once this is done, take your finger and pull the other end of the fiber.
You are now ready to do the next step.
You will use a hammer to hit the fiber at the mark.
The hammer will make the fibers bend.
You might be able make a little more bend by using a sharp pencil.
Then, using a straightedge, you can pull the bent pieces apart.
Once you have pulled the bent parts apart, you are ready to use your pliers.
Once again, the pliers should be very straight.
Be careful not too much bend and you should be happy with the result.
Now you have a good picture of what is wrong with the fiber top of a fiberglass car.
It is bent and warped.
The bent part looks like it is a part of the wheel.
There is a lot of dust on the bent portion of the tire.
You would be hard pressed to find a fiber in a fiber glass car that is not damaged.
The fiber also has a large bead of dust that is sticking to it.
To fix this problem, you will need the following items:First, remove the fiber that you used to fix your fiberglass tire.
The problem is that it is sticking together, so remove it and clean up the dust.
Then you will want to replace the fiber as well.
Do this by taking it apart and cutting the fiber in half, and putting the pieces back together.
Once both parts are done, you should now be able fix the broken part.
Take your flathead pliers and carefully pry the fiber off of the broken portion of your fiber.
Make it as small as possible, but not too small.
Make the bend as small and as straight as possible by using the awls and pliers on the broken fiber.
Now, the bent portions of the two fiberglass sections should be together.
The fiber should now look like this.
You may be able replace the broken section with a new piece of fiberglass.
You do not want to do this if the broken piece has not been fixed.
Now that you have fixed the fiber to the fiber itself, you have two options.
If both the fiber and the part are damaged, the fiber will likely crack.
If one part of a car is damaged, you might be better off just fixing one part, as that one part will be less prone to failure.
If both the parts are repaired, the problem will go away.
Now that you know how to repair fiberglass, you need to fix a fiber tube.
In order to fix this fiber tube, you first need to take out some of the fibers.
Use a nail, or a flat head screwdriver, to cut them out.
Then put the two pieces back in the fiber piece and repair it as you would a normal fiberglass tube.
Once the repair is done and the fiber tube is back in its place, you now have a new fiberglass to fix.
Make your mark with a flat piece of paper and cut a hole.
Then fill the hole with water.
This will allow the water to drain into the fiber while it is still attached.
Now fill the tube again and repeat the process.
Once it is finished, fill the fiber again and fix the tube.
If the fiber tubes are too short or you do not have the right size, you could use a drill to dig a hole in the bottom of the tube to put a bit of fiber inside.
Then use a sharp awl and push